衢州機械密封混流泵價格近期行情

混流泵

3、安裝基礎：要求土質堅實牢固。

  4、水泵安裝時，必須保證泵軸的水平位置。

  5、進水管末端應浸入水平面以下一米左右，但須離開泥底半米左右。

  6、水泵安裝好后，計算允許吸上高度和揚程，在水位穩定的條件下，要求為規定數量值的0.8~1.2倍范圍，否則水泵不會正常運行

I.

Installation Principle

 1. Installation

Height: Cidering the height according to the rainy season or dry season.The suction

vacuum

height can

not be higher than the adsorbing height.

 2. Installation

Location:The location is better to close to the water source as p  as

can.It should be not

only

keeping the safety but also shortening the water inlet pipe and reduce the

headloss

 3、水泵出水量不足

 The waer yield

 of water is not enough

 1、進水管路或葉輪有水草雜物

 2、轉速過低

 3、輸水高度過高

 4、泵蓋及葉輪磨損間隙過大

 5、填料進氣

 6、馬力不足

 7、進水管口插入水中深度不夠

 1. There are waterweeds and sundries in

 inlet pipes or impeller

 2.The rotate speed is too low

 3.Water delivery height is too high

 4.The attrition gap between pump cover

 and impeller is too large

 5.The padding is air in

 6.The horsepower is not engough

 7.The depth of inlet pipe under water is

 not enough

 1、清除水草雜物

 2、調整轉數

 3、降低輸水高度

 4、用紙墊調整間隙至正常

 5、壓緊或更換填料

 6、加大馬力

 7、增加插入水中深度至一米左右

 1.Clear the waterweeds and sundries

 2.Ajust the rotate speed

 3.Reduce the water delivery height

 4.Add paper washers to adjust the gaps

 5.Compact or change padding

 6.Increase the horsepower

 7.Make the depth of inlet pipe under

 water to one meter

按介質分類清水泵、污水泵、海水泵、熱水泵、熱油泵、稠油泵、機油泵、重油泵、渣油泵、瀝青泵、雜質泵、渣漿泵、沙漿泵、灰漿泵、灰渣泵、泥漿泵、水泥泵、混凝土泵、粉末泵、酸堿泵、空氣泵、蒸汽泵、氧氣泵、氨氣泵、煤氣泵、血液泵、泡沫泵、乳液泵、涂料泵、硫酸泵、鹽酸泵、膠體泵、酒精泵、啤酒泵、葡萄酒泵、巧克力泵、奶泵、淀粉泵、麥汁泵、牙膏泵、鹽鹵泵、鹵水泵、堿液泵、熔鹽泵、油脂泵、 、化肥泵、藥劑泵、氣液泵、油劑泵、化纖泵、紡絲泵、劑量泵、油漆泵、果漿泵、紙漿泵、胰島素泵、濃漿泵、氣泵、水泵、油泵